Patton-electronic 1058 Manuale Utente

USER MANUAL VLINK MODEMModel 1068 and 1058 SALES OFFICE(301) 975-1000TECHNICAL SUPPORT(301) 975-1007 Part# 07M1068-UMDoc# 05816U2-001Rev. ARevised 1

10 6. Connect the Ethernet interface (refer to section 3.4, “Connecting the 10/100Base-T Ethernet Interface” on page 11). 3.3 CONNECTING THE TWIS

11 The terminal block connector on the VLINK modem's twisted pair inter-face is polarity insensitive and is wired for a two-wire interface.

12 3.5 CONNECTING THE POTS/ISDN LINE The RJ-45 port labeled “POTS/ISDN” is the POTS/ISDN interface. A tele-phone or an ISDN device may be connected

13 4.0 CONFIGURATION The Model 1068 VLINK modem has eight DIP switches for configuring the unit for a wide variety of applications. This section des

14 Figure 9. Model 1068 standalone modem DIP switch orientation Figure 10. Model 1068 rack card DIP switch orientationPowerVLINK ModemLinkQOLVLINKL

15 4.2 CONFIGURING DIP SWITCH S1 DIP switch S1 is where you configure the VDSL line rate, symmetric or asymmetric, Ethernet full auto negotiation cap

16 Table 3: Model 1068 Asymmetric VDSL Line Rates Selection Chart S1-2 S1-3 S1-4Asymmetric Line Rates DS/US * *. DS = downstream, US = upstream Note

17 5.0 OPERATION Once the VLINK modems are properly installed, they should operate transparently. No user settings required. This section describes

18 Table 5: Front panel LED description for standalone modem LED Description Power On (green) when power is applied to the unit. Off when no powe

19Figure 12. VLINK modem rack card front panelTable 6: Front panel LED description for rack card modemLED DescriptionPower Solid GREEN to indicate the

2 CONTENTS1.0 Warranty Information ... 4 1.1 Radio and TV Interference (FCC Part 15) .

20APPENDIX ASPECIFICATIONSA.1 LAN CONNECTION• Unshielded RJ-45, 10/100Base-T, IEEE 802.3 Ethernet• VDSL Connection: RJ-45 and Terminal BlockA.2 TRAN

21External AC and DC options:• AC: 120 VAC, 220 VAC, and UI (120–240 VAC)• DC: 12 VDC, 24 VDC and 48 VDCA.8 TEMPERATURE RANGE32–122°F (0–50°C)A.9 HU

22APPENDIX BMODEL 1068 SERIES FACTORY REPLACEMENT PARTS AND ACCESSORIESPatton Model # DescriptionBase Models1068DVRC/CO CO Variable Rate VDSL RC CO Ra

23*Only required with optional UI power supply (08055DCUI)48V-PSM 48 VDC Input AdapterPower Cords*0805US American Power Cord0805EUR European Power Cor

24APPENDIX CVLINK SERIES INTERFACE PIN ASSIGNMENTC.1 10/100BASE-T INTERFACERJ-45• Pin 1: TX+/RX+• Pin 2: TX-/RX-• Pin 3: RX+/TX+• Pin 6: RX-/TX-• Pin

25APPENDIX DDISTANCE CHART, BASED ON 24 AWG (0.5 MM)Note DS/US = Downstream/Upstream. Symm Line Rate Distance in feet (km)6.25 Mbps 4,500 (1.37)9.38 M

26Notes_______________________________________________________________________________________________________________________________________________

27Copyright © 2006Patton Electronics CompanyAll Rights Reserved.

3 Terminal Block (1068DV/TB45 Only) ... 24 C.3 POTS/ISDN Interface ...

4 1.0 WARRANTY INFORMATION Patton Electronics warrants all VLINK modem components to be free from defects, and will—at our option—repair or replace

5 The safety advice in the documentation accompanying this product shall be obeyed. The conformity to the above directive is indicated by the CE sign

6 2.0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and

7 • Available in rack-mount or standalone configurations• Made in the USA 2.2 DESCRIPTION The Patton Electronics VLINK/CO and VLINK/CP VDSL modems pr

8 3.0 INSTALLATION Because the VLINK modem requires no configuration, it can be installed quickly. If you are installing a standalone unit, refer to

9 3.2 RACK CARD INSTALLATION The VLINK modem rack card comprised a front card and a rear card.Do the following to install the cards into the rack ch