Patton-electronic CopperLink Ethernet Extenders 2168A Manuale Utente

USER MANUALCopperLink™ Ethernet Extenders Models 2168A and 2158ASALES OFFICE(301) 975-1000TECHNICAL SUPPORT(301) 975-1007Part# 07M2168A-UM Rev. CRevi

103.2 GROUNDING THE COPPERLINK ETHERNET EXTENDERBefore installing the CopperLink Ethernet Extender, it is important to establish a good grounding con

11The RJ-45 connector on the CopperLink Ethernet Extender's twisted pair interface is polarity insensitive and is wired for a two-wire inter-face

12Using a Ferrite Clamp to Connect the Line InterfaceConnecting the ferrite clamp to the RJ-45 port. To connect the ferrite clamp to the RJ-45 port:

13Connecting the ferrite clamp to the terminal block. To connect the ferrite clamp to the terminal block: 1. Place the cable inside the ferrite cla

143.4 CONNECTING THE 10/100BASE-T ETHERNET INTERFACEThe RJ-45 port labeled Ethernet is the Auto-MDIX10/100Base-T inter-face. This port is designed to

153.5 CONNECTING POWERAn external AC or DC power supply is available separately. This connec-tion is made via the barrel jack on the rear panel of th

164.0 CONFIGURATION The CopperLink Models 2168A and 2168A/TB45 have an eight-position DIP switch for configuring the unit for a wide variety of appli

174.2 CONFIGURING DIP SWITCH SWDIP switch SW is where you configure the CopperLink line rate, and if the rate is symmetric or asymmetric. Switches SW

185.0 OPERATIONOnce the CopperLink Ethernet Extenders are properly installed, they should operate transparently. No user settings required. This sect

19Table 4: Front panel LED description for the 2168ALED DescriptionPower On (green) when power is applied to the unit. Off when no power is applied to

2CONTENTS1.0 Warranty Information ... 41.1 Compliance...

20APPENDIX ASPECIFICATIONSA.1 LAN CONNECTION• Unshielded RJ-45, 10/100Base-T, IEEE 802.3 Ethernet• CopperLink Connection: — 2168A/TB45: RJ-45 and Ter

21A.7 POWER SUPPLYInput power: 5 VDC, 1APower consumption: 560 mA at 5 VDC (typical)External AC and DC options:• AC: 120 VAC, 220 VAC, and UI (120–24

22APPENDIX BMODEL 2168A AND 2158A SERIES FACTORY REPLACEMENT PARTS AND ACCESSORIESPatton Model # DescriptionBase Models2158A/E-2PK CopperLink 12.5 Mbp

23Power Supplies08055DCUI 08055-120-5-1100-240VAC (+5V reg. DC/2A) Universal Input Adapter. 120 VAC (+5V reg. DC/1A) Input Adapter12V-PSM 12 VDC Input

24APPENDIX CCOPPERLINK SERIES INTERFACE PIN ASSIGNMENTC.1 10/100BASE-T INTERFACERJ-45• Pin 1: TX+/RX+• Pin 2: TX-/RX-• Pin 3: RX+/TX+• Pin 6: RX-/TX-

25APPENDIX DDISTANCE CHART, BASED ON 24 AWG (0.5 MM)NoteDS = downstream from L unit to R unit US = upstream from R unit to L unitSymm Line Rate Distan

26NOTES_______________________________________________________________________________________________________________________________________________

27NOTES_______________________________________________________________________________________________________________________________________________

28NOTES_______________________________________________________________________________________________________________________________________________

3B Model 2168A and 2158A Series Factory Replacement Parts and Accessories... 22C CopperLink Series Interface Pi

41.0 WARRANTY INFORMATIONPatton Electronics warrants all CopperLink Ethernet Extender compo-nents to be free from defects, and will—at our option—rep

51.2 RADIO AND TV INTERFERENCE (FCC PART 15)This equipment generates and uses radio frequency energy, and if not installed and used properly—that is,

6Note Packages received without an RMA number will not be accepted.1.6 SAFETY WHEN WORKING WITH ELECTRICITY• This device contains no user serviceable

72.0 GENERAL INFORMATIONThank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is

82.2 DESCRIPTIONThe Patton Electronics CopperLink/L and CopperLink/R Ethernet Extenders provide high-speed LAN connections between peered Ether-net L

93.0 INSTALLATIONBecause the CopperLink Ethernet Extender requires no configuration, it can be installed quickly. Note If asymmetric transmission or